​Bell & Gossett series 1510 pump for low energy consumption

Bell & Gossett series 1510 pump for low energy consumption

The Bell & Gossett series 1510 pumps are designed to cut the cost significantly across installation, life-long maintenance and functioning.

These pumps are base mounted end suction design that comes with a base mounted volute which lets you remove and service the entire rotating assembly without upsetting the pump piping, alignments and electrical motor connections.

Advantages of a Bell & Gossett series 1510 pump

• The exceptional seal design is confirmed to be very useful to many clients over the years. It does not need any particular external flushing necessities, since the design offers steady efficient flushing action within. This benchmark feature provides most seal face lubrication, heat dissipation and waste removal without susceptible, external flush tubing. The internal flushing process passes two and a half to three times the gush over the seal faces.
• All Bell & Gossett Series 1510 pumps come with a standard with a volute foot situated directly under the pump volute. This integrally cast foot makes sure that the alignment between the volute and motor assembly is well positioned. Without the proper support under the volute, the piping weight single-handedly will cause deformation which can lead to an early and untimely breakdown of the bearings, shaft and mechanical seal. This feature is especially important on hot water applications. The Series 1510 volute foot offers a strong base and removes the deflections which would or else occur in volute lacking proper support during the usual thermal opening out of the system piping against the volute.
• Unlike conventional style couplings, the Center Drop-Out Spacer Coupling in these pumps permits the eradication of the bearing frame and rotating element without hindering the pump end pipe alignment or motor electrical connections.
• There is accurate computer controlled impeller balancing in these pumps. The Bell & Gossett 1510 impellers are balanced to ANSI/HI 9.6.4-2009, balance grade G6.3 standards. This type of computer balancing Impellers ensures a quiet, competent, vibration free routine. The Diameters are computer selected at the factory to provide assurance that your capacity needs will be met.
• The coupler guard meets with the ANSI B15.1 and OSHA 1910.219 standards. The guard assure enhanced protection against possible serious injuries and is criterion on all 1510 pumps. The guards contain slotted viewing window for an effortless inspection procedure.
• The Bell & Gossett heavy duty base plate is made mandatory on every Bell & Gossett Series 1510 pump. Contrasting to rolled steel and “C” channel base plates, the Series 1510 base plate offers a fabricated heavy duty saddle assembly, full seam welds, closed base plate ends and an open top to provide ease of access for proper equipment grouting.
• The Patented i-ALERT Condition Monitor constantly notes the vibration and temperature at the outboard bearing and routinely points out when pre-set levels of vibration and temperature have been surpassed, so that modifications can be made before failure happens. A visual display of pump health makes inspections more resourceful and precise. This onboard pump intelligence promotes minimize life-cycle expenses while increasing the performance.
• All the operating system drives are built with a NEMA 12 area rating to provide a safe drive operation in case of falling dirt and water. The drives also have a temperature controlled cooling fan to ensure continuous operation and a powerful and advanced power system plan.
• The seismic potential of the pump will let it endure a horizontal load of 0.5g, not including piping and/or fasteners used to secure the pump to mounting pads or to the floor, without harmfully affecting pump functioning.

Technical Specifications

• Impellers are balanced to Hydraulic Institute Standards ANSI/HI 9.6.4-2009.
• The allowable residual unbalance in the impeller rotating assembly conforms to ANSI grade G6.3 (Ref. ISO 1940).
• ANSI Balance Quality Grades of G2.5 and G1 for the rotating assembly are also available.
• Series 1510 pumps are capable of withstanding a horizontal load of 0.5g* without adversely affecting pump operation.

If you are thinking about purchasing the Bell & Gossett series 1510 pumps, browse through our pumps category and get the best deal. Online purchases can be tricky, but we hold a reputation for premium and reliable services and quality products for our customers.