Hoffman

405153 Hoffman Thermodisc Steam Trap 3/4" TD6526

(No reviews yet) Write a Review
MPN:
405153
Condition:
New
Availability:
This Item Usually Ships The Same Day!
Shipping:
Calculated at Checkout
$524.95

Description

405153 Hoffman Thermodisc Steam Trap 3/4" TD6526.

Information:

Thermodisc Steam Traps:

Thermodisc steam traps use flash steam velocity and pressure to move a free-floating disk to open and close a valve. Because the disc is the only moving part, the traps are rugged and resistant to damage. This type of trap provides dependable performance for applications with light to moderate condensate loads. Thermodisc traps are excellent for high-pressure drip and steam tracing applications.

Operation of Thermodisc Traps:

At start-up, the disc is pushed off the seat by the inlet pressure and is held open by the impact force of the condensate hitting the disc. As the condensate nears saturation temperature, flash steam will enter the seat-disc chamber at high velocity, lowering the pressure on the bottom of the disk. Some of the flash steam escapes to the area above the disc, causing the pressure above the disc to increase, pushing the disc closer to the seat.

At the instant the disc snaps closed on the seat, the pressure above the disc is approximately equal to the upstream line pressure. The disc is held closed because the pressurized area above the disc is much larger than the inlet area. The pressure above the disc decreases either by steam condensation or by non condensables being removed via the micro-bleed channel on the disc. When the pressure is low enough, the disc is pushed off the seat and the process is repeated.

Characteristics of Thermodisc Traps:

  • Completely drains condensate at saturation temperature.
  • Condensate is discharged close to steam temperature at all operating pressures.
  • May be installed vertically, to drain trap body when steam is off, to prevent freezing.
  • Compact size allows fitting in “tight” locations.
  • Increase in cycling rate produces a distinct audible clicking sound that gives indication of wear before failure.
  • Easily serviced in-line with replaceable seat and disc.
  • Will tolerate water hammer, superheat, corrosive condensate and vibration.
  • Audible “click” as disc seats may produce objectionable noise.
  • Does not operate well at extremely low pressures or extremely high backpressure.
  • Drains condensate from compressed air lines.
  • Limited air-handling capability.
  • Small passageways are sensitive to dirt, preventing tight closing of disc.

Primary Applications of Thermodisc Traps:

  • Steam tracer lines where maximum temperature is required.
  • Outdoor applications including drip traps on steam machines.
  • Drying tables.
  • Tire mold press and vulcanizing equipment.
  • Dry kilns.
  • Pressing machines.
  • Rugged applications (superheat & water hammer).

Features and Benefits:

  • One piece body eliminates internal gaskets and leak paths.
  • All stainless steel components provide dependable operation in severe applications.
  • Available in sizes up to 1 inch.
View AllClose

Warranty Information

Warranty: Quoted prices include standard factory warranties. Warranty requires install, start-up and operation as per the manufacturers IOM. Job Site Assistance: By Others Start-Up: By Others Commissioning: By Others: These services, if a project requires start up, they are responsibility of contractor or commissioning agent. Owner training assistance, as outlined in any equipment specifications the responsible of the commissioning agent. Clarifications & Exclusions 'ALTERNATES' are offered for consideration and will always be subject to the engineer's and owners approval. Excludes any seismic calculations or supports, coatings other than factory standard. Terms: prices are quoted are "each" (unless stated otherwise) and FOB point of origin with no freight allowed freight ships via common ground carrier, and inside continental US Only - any special shipping requirements to be responsibility of purchaser. We offer all prices less tax, with a validity of 30 days from the date quoted and all sales are final. Once items have shipped and left the warehouse National Pump Supply is not responsible for any damage caused during the shipping process. You must contact the shipper directly and file a claim with the shipping company. Lead Time: All prices offered are based on standard factory lead times (or) as stated within quotation. Expedited shipments may be available at an additional charge. Contact your Sales Engineer for the ETA of any specific equipment on any order or quotation.
View AllClose